Digital Components

DIN valve connectors with improved strain relief.

Standard internal thread DIN valve connector, IP65 rated.
Available with different thread style, gaskets and circuitry.
Conforms to EN 175301-803

* Zoekterm: digitaal, digital, componenten, components
The ZL-24-01 power supply is used with a 230 V, 50 Hz AC network supply to power devices requiring direct current.


* Output power supply 2x24 V DC
* Maximum output current 2 × 50 mA
* Indication of presence of output voltage
* Permanently resistant to short circuits and excess voltage
* Casing can be fitted on a standard rail (TS35, TS32)

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The ZL-24-08 power supply is typically used with a 230 V, 50 Hz AC network supply to power devices requiring direct current.


* Maximum output current 800 mA
* High energy efficiency
* Indication of the presence of output voltage
* Permanently resistant to short circuiting and excess voltage
* Overvoltage protection Casing can be fitted on a standard rail (TS35, TS32)

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The SP-02 signal isolator provides galvanic separation of an input signal (0/4...20 mA) and converts it.


* Single circuit or dual circuit version in 12,5 mm wide casing
* Accuracy 0,16%
* Casing can be fitted on a standard adapter (TS35)

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The ZSP-41 provides galvanic separation of an input signal (4 ÷ 20 mA, 0 ÷ 20 mA, 0 ÷ 10 V, 0 ÷ 20 V) and converts it.


* Full galvanic separation of circuits (IN-OUT, IN-SUP, OUT-SUP)
* Ability to select input and output signals
* Ability to use input line to power a two-wire transmitter
* Casing can be fitted on a standard rail (TS35)

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The SP-11 signal isolator provides galvanic isolation of an input current or voltage signal and converts it.


* Single circuit or dual circuit version in 12,5 mm wide casing
* Opto-electronic galvanic separation (IN-OUT)
* Ability to select input signal
* 9...36 V power supply in the output signal loop
* Casing can be fitted on a standard rail (TS35)

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The SP-11 signal isolator provides galvanic isolation of an input current or voltage signal and converts it.The ZS-30Ex1 power supply and isolator is a partially intrinsically safe device with an external (input) intrinsically safe circuit.

* Ex-rated intrinsically safe Full galvanic separation of circuits (IN-OUT, IN-SUPPLY, OUT-SUPPLY)
* Accuracy 0,1%
* Casing can be mounted on a standard TS35 rail

* Zoekterm: digitaal, digital, componenten, components, Aplisens
The ZS-31Ex1 power supply and isolator is a partially intrinsically safe device with an external (input) intrinsically safe circuit.


* Ex-rated intrinsically safe
* Full galvanic separation of circuits (IN-OUT, IN-SUPPLY, OUT-SUPPLY)
* Accuracy 0,1%
* Casing can be mounted on a standard rail (TS35, TS32)

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The UZ-2 protection circuit is designed to provide overvoltage protection for measurement transmitters and auxiliary devices.



* Zoekterm: digitaal, digital, componenten, components, Aplisens

with data logging capabilities 3.5"/5.7 TFT, 320 x 240 pixels, touchscreen navigation.



* compact multichannel controller with data logging capabilities
* analog / digital / universal inputs
* thermocouple / RTD inputs
* counter / flowmeter / ratemeter inputs
* current or relay / SSR outputs
* USB Host port for flush data storage
* free configuration and recording software
* 3.5"/5.7 TFT, 320 x 240 pixels, touchscreen navigation

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The industrial data logger PMS-90R is designed to record and display current values as well as to present technological parameters in the form of graphs.

* Up to 8 inputs 0/4 20mA or PT100/PT500/PT1000
* 1 digital input for recording release
* 2 relay outputs in standard (optoMOS)
* USB Host port for flush data storage
* RS-485 / Modbus RTU
* Power supply 19V ÷ 50V DC, 85 ÷ 260V AC Free configuration and recording software.

* Zoekterm: digitaal, digital, componenten, components, Aplisens

The WW-11ALW digital indicator is designed to be used with any device with a 4...20 mA.


* Backlight display 5 × 10 mm
* Current input 4...20 mA
* Aluminum, wall or pipe mounted casing
* IP66
* Intrinsic safety certificate

* Zoekterm: digitaal, digital, componenten, components, Aplisens
The indicator is typically used to give an additional local reading when carrying out remote measurement of absolute or relative pressures.


* Zoekterm: digitaal, digital, componenten, components, Aplisens
Programmable PMS-920, PMT-920 indicators are applicable to cooperation with the transmitters having a standard current or voltage output signal.


PMS-920 and PMT-920 meters enables the following parameters to be programmed:

* type of input signal: 4...20 mA or 0...20 mA, 0...5 V, 0...10 V, 1...5 V or 2...10 V, Pt100
* measured value display range and decimal point position;
* level and hysteresis of action of relays;
* state of contact during alarm;
* password restricting access to the programming menu;
* display filtering level.
* Colour of display: red, green.

* Zoekterm: digitaal, digital, componenten, components, Aplisens
The programmable PMS-970T indicator is applicable to cooperation with the transmitters having a standard current or voltage output signal.


* Universal measuring input
* 4...20 mA, 0...20 mA or 0...10 V 4 relay outputs: 1 A, 230 V AC
* 4 × 7 mm red LED display
* Integrated power supply 24 V DC
* Additional options:
** Power supply 24V AC/DC
** passive current output
** RS-485 digital output

* Zoekterm: digitaal, digital, componenten, components, Aplisens
The programmable PMS-970P indicator is applicable to cooperation with the transmitters having a standard current or voltage output signal.


* Universal measuring input
* 4...20 mA, 0...20 mA or 0...10 V 4 relay outputs: 1 A, 230 V AC
* 4 × 20 mm red LED display
* Integrated power supply 24 V DC
* Additional options:
** Power supply 24V AC/DC
** passive current output
** RS-485 digital output

* Zoekterm: digitaal, digital, componenten, components, Aplisens
The programmable PMS-620N indicator is applicable to cooperation with the transmitters having a standard input current and voltage signals.


* 4 × 20 mm red LED display Universal measuring input
* 4...20mA, 0...20mA or 0...10V
* Two relay outputs: 1 A, 230 V AC
* RS-485 digital output
* Integrated power supply 24 V DC Wall mounted casing

* Zoekterm: digitaal, digital, componenten, components, Aplisens
- article code = APLI-RS485-USB-CONVERTER
- code APLI = Manufacturer
- code RS485.USB.CONVERTER = Converter
- article code = APLI-PP
- code APLI = Manufacturer
- code PP = Junction Box *
* ambient temperature : -30 to +80 degrees Celsius
* material : Gray Polycarbonate with a Polyurethane gasket, IP 65 degree of protection
* cable gland cable diameter : 5,0 mm ÷ 10,0 mm
* cable gland thread length : 8,0 mm
* cable gland hexagon size : 22 mm
* connectors : separable - plugs (they can be removed from the socket in order to install the wires)
* connector Pins : straight
* number of pins : 2 × 4
* max wire diameter : 2.5 mm2

A collection of different digital products, etc. Indicators, displays, data loggers, relay outputs, power supplies, overload protection & signal converters.

Please accept cookies to help us improve this website Is this OK? Yes No More on cookies »